View L7055-04_785607.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HIGH-POWER INFRARED PULSED LASER DIODE
L7055-04
FEATURES
High output power ( ep 0W) High speed rise time (tr=0.5 ns typ.)
APPLICATIONS
Laser rader Range finder Excitation light source Optical trigger Security barrier
Figure 1: Dimensional Outline (Unit: mm)
Glass Window LD Chip 9.0 -0.1 5.7 2.8 0.2 0.3 0.5 7.0 0.5 (Pin Connection) 5.1
+0
ABSOLUTE MAXIMUM RATINGS
Parameter Pulsed Foward Current Reverse Voltage Pulsed Radiant Output Power Pulse Duration (FWHM) Duty Ratio Operating Temperature Storage Temperature Symbol IFP VR
ep
Value 30 2 40 100 0.075 -30 to +85 -40 to +125
Unit A V W ns %
Anode Cathode NC (Case)
0.45 2.54 Side View 1.0 0.4
tw DR Top Tstg
1.5
2.4
Bottom View
Anode Cathode
ELECTRICAL AND OPTICAL CHARACTERISTICS (Ta=25
Parameter Pulsed Radiant Power Peak Emission Wavelength Spectral Radiation Half Bandwidth Forward Voltage Rise Time Beam Spread Angle : Parallel : Vertical Lasing Threshold Current
Note: General operating condition
ep
)
Typ. 870 4 6 0.5 8 32 1 Max. 10 35 Unit W nm nm V ns degree degree A
Symbol
ep
Condition IFP=20A
Min. 20 -
p VF tr FWHM IFP=20A Ith
W, tw 0 ns, Repetition frequency kHz
IFP=20A
6 29 -
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. C 1998 Hamamatsu Photonics K.K.
HIGH-POWER INFRARED PULSED LASER DIODE L7055-04
Figure 2: Typical Radiant Power vs. Pulsed Forward Current
(Ta=25 )
Figure 3: Typical Emission Spectrum
(Ta=25 100 )
40
()
RELATIVE RADIANT POWER (%)
80
ep
30
PULSED RADIANT POWER
60
20
40
10
20
0 0 10 20 30
0 830
850
870
890
910
PULSED FORWARD CURRENT IFP (A)
WAVELENGTH (nm)
Figure 4: Typical Directivity
(IFP=20 A, Ta=25 100
Parallel Direction Vertical Direction
)
RELATIVE RADIANT POWER (%)
80
60
Top View
Top View
40
20
0 40
30
20
10
0
10
20
30
40
ANGLE (degree)
Handling Precautions for L7055-04 1. Precautions for handling The LD (laser diode) may be damaged or its performance may deteriorate due to such factors as electrostatic discharge from the human body, surge voltages from measurement equipment, leakage voltages from soldering irons, and packing materials. As a countermeasure against static electricity, the device, operator, work place and measuring jigs must all be set at the same electric potential. In using LD, observe the following precautions: To protect the device from static electricity charges which accumulate on the operator or the operator's clothes, use a wrist strap etc. to ground the operator's body via a high impedance resistor (1M ). A semiconductive sheet should be laid on both the work table and the floor in the work area. When soldering, use an electrically grounded soldering iron with an isolation resistance of more than 10M . For containers for transportation and packing, use of antistatic material (material that minimizes the generation of static change when rubbed against or separated from itself or other similar materials). 2. Precautions for mounting (1)Lead forming To form the leads, hold the base of the leads securely and bend them so that no force is applied to the package. Lead forming should be done before soldering. (2)Cutting off the leads If leads are out when still at a high temperature, this may cause an electrical discontinuity. Always cut off the leads when they are at room temperature. Never cut off the leads immediately after they are soldered.
(3)Soldering Using a low-temperature melting solder (below 200 ), solder the leads at the temperature and dwell time specified as follows. Maximum Soldering Temperature: 230 Maximum Soldering Time: 5 seconds (1 second for devices having a lead length less than 2mm) If these conditions cannot be met, it is recommended that some form of heat sink be used at the base of the lead so that the solder heat is not conducted to the package. Also be careful not to apply excessive force to the leads during soldering. Soldering at excessive temperatures and dwell times may cause the roots of the leads to crack, resulting in performance deterioration. This sometimes leads to wiring breakage. If the leads are soldered while external force is applied to the device, the residual force tends to degrade device performance. Care should also be taken not to apply force to the leads during soldering. In addition, when soldering an LD. use a soldering iron with its metallic parts grounded to prevent damage to the device from static discharge. Do not use any flux which is highly acidic. alkaline or inorganic because it may cause the component leads to erode. Use a rosin flux. 3.Protection against laser beams The LD is classified into class 3B according to the laser product standards of the lEC825-1 (Radiation safety of laser products Part1: Equipment classification, requirements and user's guide). The operator must avoid eye or skin exposure to the laser beam. When viewing the laser beam, be sure to wear safety goggles that block infrared radiation.
http://www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., International Sales Division 325-6, Sunayama-cho, Hamamatsu City, 430-8587, Japan, Telephone: (81)53-452-2141, Fax: (81)53-456-7889
U.S.A.: Hamamatsu Corporation:360 Foothill Road, P.O. BOX 6910, Bridgewater, N.J. 08807-0910, U.S.A.Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658, E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33(1) 69 53 71 00, Fax: 33(1) 69 53 71 10, E-mail: france@hamamatsu.com United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44)1707-294888, Fax: (44)1707-325777, E-mail: info@hamamatsu.co.uk North Europe: Hamamatsu Photonics Norden AB: Smidesv gen 12, SE-171-41 Solna, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01, E-mail: info@hamamatsu.se Cat. No. LLD1004E02 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741, E-mail: info@hamamatsu.it
Jul. 1999 T Printed in Japan (1,000)

▲Up To Search▲

Price & Availability of L7055-04

	To Download L7055-04 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .